To order this product you must be logged into your distributor account. Not yet a M+A distributor, but interested in becoming one? Fill out this form.

Microfibre Wet Mop

Stock Product Number MOP_AMMW
Microfibre wet mops penetrate surface pores to remove tiny dust particles. They are designed for frequent changes to reduce cross-contamination.
  • Helps eliminate cross-contamination with mop pads designed for frequent changes
  • Made with Velcro backing for quick, easy changes
  • Available with different binding colors for sorting by use or area
  • Commercially launderable

Stocked in blue with blue binding and blue with red binding in the following sizes for quick shipping: 5" x 18" and 5" x 24"

The following sizes are stocked:
5" x 18" (12.7 x 46 cm) blue with blue binding
5" x 24" (12.7 x 61 cm) blue with red binding

Additional sizes and binding colors are available, but are not stocked and require additional lead time.

The following procedure for machine washing microfiber mops will assure maximum performance and longevity of 200 to 300 washing.

Do not use bleach to remove stains or for any other reason. Bleach decreases the effectiveness and durability of the microfiber product. Do not use fabric softener.

  1. Flush, High, 80°F - 27°C for 2 minutes.
  2. Flush, High, 120°F - 50°C for 2 minutes.
  3. Break/Suds, Low, 140°F - 60°C for 10 minutes
    6oz. built (non solvent) detergent for each 100 lbs. - ph 8.5 - 11.5 max.
  4. Rinse/Extract, High, 120°F - 50°C for 3 minutes.
  5. Rinse/Extract, High, 80°F - 27°C for 2 minutes.
  6. Rinse, High, Cold for 2 minutes with ph 7.0 to 9.0

Additional Processing Information:

  • Centrifugal Extraction: Bring to full speed (300 rpm) for 4 minutes and release.
  • Hydraulic Extraction: NOT RECOMMENDED
  • Drying: Compared to traditional mops, drying time is significantly reduced with microfiber products. Drying times will vary depending on your geographical location, equipment and the environment and load size. When programming auto dryer settings, monitor temperature for the first 3-6 loads, stop temperature when 120°F is reached, then begin cool down after set point has ran for 3-5 minutes.
  • Air Drying is RECOMMENDED but if you must dry using gas or steam heat, start by tumbling these mops at 140°F incoming temperature, 100°F exhaust( If available on your equipment, reverse the dryer drum during the drying cycle. It reduces the drying time and will not create heat pockets in the mop/yarns prolonging their service life). Cool to 90 - 100°F before unloading.
  • MOPS SHOULD NOT BE FULLY DRY; moisture content should be approximately 20-25%, unless they are being poly wrapped directly from dryer. Microfiber is the perfect item to air dry at the end of your production shifts if you have large dryers that require cool down of the drum support rollers at the end of the production day.  Place the microfiber items in the drum before you start the dryer and allow them to tumble while doing this cool down even if you only have a small quantity of microfiber items. It is not wasted energy and it will prolong the life of your products.

Notes:

  • Over time, the use of harsh chemicals such as those contained in bleach and the use of fabric softeners will reduce the performance and longevity of the microfiber products.
  • Do not WASH/STORE OR TRANSPORT microfiber mops with terry towels, regular mops or any other product that has cotton or linting capabilities.
  • Separate different colored microfiber mops before their first wash. 

If you require additional information or require further assistance, please call Golden Star customer service department at 1-800-821-2792 or 1-816-842-0233 or email [email protected]